Just got a new engine and turbo installed in my 2007 CX-7 AWD. I am new to tuning and looking for some assistance.
Mods are:
Corksport turbocharger (MS3/MS6)
Corksport Stage II air inlet pipe + SRI
Corksport 3.5bar MAP sensor
Also how do you disable TCS with the software?
Tune Turbo Upgrade
Re: Tune Turbo Upgrade
Any help would be greatly appreciated. Mechanical work is just about done and vehicle should be road ready tomorrow. Need to have a proper tune to ensure best performance and reliability. Thanks.
2007 Mazda CX-7 AWD Grand Touring - Electric Blue Mica
CST4 turbo, CS 3.5bar MAP, CS Stage II SRI w/ TIP, dual port BOV/BPV, 3 port EBCS, 3" TBE w/ Magnaflow muffler, KYB Excel-G shocks, deleted catalytic converters
Disabled EGR, 2nd O2, VTCS
CST4 turbo, CS 3.5bar MAP, CS Stage II SRI w/ TIP, dual port BOV/BPV, 3 port EBCS, 3" TBE w/ Magnaflow muffler, KYB Excel-G shocks, deleted catalytic converters
Disabled EGR, 2nd O2, VTCS
Re: Tune Turbo Upgrade
You can contact StratifiedAuto or FreekTune.
2008 Cosmic Blue Mazda 3MPS
Built engine + WMI + GTX3071 gen2, ~550BHP @35PSI
2008 Icy Blue Mazda CX7
Built engine and stock exhaust (YES!!), JBR3" + GTX2867 gen2 + Autotech HPFP, self-tuned to 360-ish BHP
Built engine + WMI + GTX3071 gen2, ~550BHP @35PSI
2008 Icy Blue Mazda CX7
Built engine and stock exhaust (YES!!), JBR3" + GTX2867 gen2 + Autotech HPFP, self-tuned to 360-ish BHP
-
Project_cx7
- Posts: 35
- Joined: July 19th, 2015, 10:37 pm
Re: Tune Turbo Upgrade
What turbo did you upgrade too?
2007 Mazda CX-7. Manley H-beam rods, Wiseco 88 mm pistons, King racing bearings, balance the crankshaft, bosch 3 bar map sensor, removed VTCS and egr, JB OCC, JB 3.5 inch intake, FMIC, Forge v1 BPV, BNR S3 turbo, 3 inch catless DP.
Re: Tune Turbo Upgrade
Corksport
2007 Mazda CX-7 AWD Grand Touring - Electric Blue Mica
CST4 turbo, CS 3.5bar MAP, CS Stage II SRI w/ TIP, dual port BOV/BPV, 3 port EBCS, 3" TBE w/ Magnaflow muffler, KYB Excel-G shocks, deleted catalytic converters
Disabled EGR, 2nd O2, VTCS
CST4 turbo, CS 3.5bar MAP, CS Stage II SRI w/ TIP, dual port BOV/BPV, 3 port EBCS, 3" TBE w/ Magnaflow muffler, KYB Excel-G shocks, deleted catalytic converters
Disabled EGR, 2nd O2, VTCS
-
Project_cx7
- Posts: 35
- Joined: July 19th, 2015, 10:37 pm
Re: Tune Turbo Upgrade
my bad I just noticed up on your first post. Have you done any internal work to the motor?
2007 Mazda CX-7. Manley H-beam rods, Wiseco 88 mm pistons, King racing bearings, balance the crankshaft, bosch 3 bar map sensor, removed VTCS and egr, JB OCC, JB 3.5 inch intake, FMIC, Forge v1 BPV, BNR S3 turbo, 3 inch catless DP.
Re: Tune Turbo Upgrade
No. Engine is brand new however.
2007 Mazda CX-7 AWD Grand Touring - Electric Blue Mica
CST4 turbo, CS 3.5bar MAP, CS Stage II SRI w/ TIP, dual port BOV/BPV, 3 port EBCS, 3" TBE w/ Magnaflow muffler, KYB Excel-G shocks, deleted catalytic converters
Disabled EGR, 2nd O2, VTCS
CST4 turbo, CS 3.5bar MAP, CS Stage II SRI w/ TIP, dual port BOV/BPV, 3 port EBCS, 3" TBE w/ Magnaflow muffler, KYB Excel-G shocks, deleted catalytic converters
Disabled EGR, 2nd O2, VTCS
-
Project_cx7
- Posts: 35
- Joined: July 19th, 2015, 10:37 pm
Re: Tune Turbo Upgrade
all stock pistons and rods?
2007 Mazda CX-7. Manley H-beam rods, Wiseco 88 mm pistons, King racing bearings, balance the crankshaft, bosch 3 bar map sensor, removed VTCS and egr, JB OCC, JB 3.5 inch intake, FMIC, Forge v1 BPV, BNR S3 turbo, 3 inch catless DP.
Re: Tune Turbo Upgrade
Yes. Block is completely stock except the bolt on mods I mentioned.
2007 Mazda CX-7 AWD Grand Touring - Electric Blue Mica
CST4 turbo, CS 3.5bar MAP, CS Stage II SRI w/ TIP, dual port BOV/BPV, 3 port EBCS, 3" TBE w/ Magnaflow muffler, KYB Excel-G shocks, deleted catalytic converters
Disabled EGR, 2nd O2, VTCS
CST4 turbo, CS 3.5bar MAP, CS Stage II SRI w/ TIP, dual port BOV/BPV, 3 port EBCS, 3" TBE w/ Magnaflow muffler, KYB Excel-G shocks, deleted catalytic converters
Disabled EGR, 2nd O2, VTCS
-
Project_cx7
- Posts: 35
- Joined: July 19th, 2015, 10:37 pm
Re: Tune Turbo Upgrade
dont push her to hard. youll bend a rod
2007 Mazda CX-7. Manley H-beam rods, Wiseco 88 mm pistons, King racing bearings, balance the crankshaft, bosch 3 bar map sensor, removed VTCS and egr, JB OCC, JB 3.5 inch intake, FMIC, Forge v1 BPV, BNR S3 turbo, 3 inch catless DP.