Search found 51 matches

by Walle
October 4th, 2021, 9:10 pm
Forum: Series I Tuning
Topic: Tune Sharing
Replies: 12
Views: 13037

Re: Tune Sharing

Toxic_RX8_ wrote: October 2nd, 2021, 5:39 pm This is what I'm running :burnrubber
would be nice to have your engine mods listed as well here before downloaded. also a short list of ecu map mods
by Walle
October 4th, 2021, 9:02 pm
Forum: Series I Tuning
Topic: New to Tuning-Looking for a Tune
Replies: 12
Views: 7687

Re: New to Tuning-Looking for a Tune

the bad thing is that he has both intake mods (MAF scaling) and engine breathing mods (VE). I would try and chase LTF by MAF and VE by short therm by following aproach. load a tune and drive for a week. log Rev, Calculated load, Short trim, Long trim for half an hour. try to "hit" 1000 to ...
by Walle
September 7th, 2021, 6:54 pm
Forum: Software Support
Topic: Another Question on Returning to stock form
Replies: 9
Views: 13262

Re: Another Question on Returning to stock form

Issue have been fully solved by Versa tuner support. For further reference. I have been given a small software to read the ecu "access codes" and I sent a LOG of that to V.T. for which they than adjusted a small program to execute. After that the Versa tuner was installed as normal. If you...
by Walle
September 4th, 2021, 6:49 am
Forum: Software Support
Topic: DTC disable function is not working as expected
Replies: 12
Views: 14551

Re: DTC disable function is not working as expected

Having the secondary O2 removed is not a problem, I have this done on my CX7 because I wanted to run leaner than stoich AFRs during cruising. Also removing the catalytic converters is not a problem either. yeap I fully agree with this. it is just so annoying to constantly keep seeing these. and hav...
by Walle
September 4th, 2021, 6:47 am
Forum: Software Support
Topic: Another Question on Returning to stock form
Replies: 9
Views: 13262

Re: Another Question on Returning to stock form

I hope I am writing this in the right section and its not a problem im taking an old thread but I do find it relevant. My mazda Rx-8 was tuned by mazdaedit long time ago. I was told Versa tuner can load the stock map on to it. I tried 2 methods: "return car to stock" - which gave this erro...
by Walle
September 3rd, 2021, 7:21 pm
Forum: Mazda RX-8
Topic: Versa Tunes recomendation (Fan temps and Idle rpm)
Replies: 6
Views: 4992

Versa Tunes recomendation (Fan temps and Idle rpm)

Hello Versa Tuner team. I have one proposition to implement in to all of your mazda tunes as this is something that is damaging to the engine on a stock ECU settings, and a lot of engines have been lost do to these particular setting that I don't se you have adjusted in any of your prebuilt tunes. P...
by Walle
September 3rd, 2021, 7:08 pm
Forum: Mazda RX-8
Topic: Air Fuel Ratio maps 1,2 and 3
Replies: 13
Views: 18563

Re: Air Fuel Ratio maps 1,2 and 3

And no, it does not have anything to do with gearing. they are used for different driving condition depending on the cars logic. best to keep all of them Copy/Pasta
by Walle
September 3rd, 2021, 7:05 pm
Forum: Software Support
Topic: DTC disable function is not working as expected
Replies: 12
Views: 14551

Re: DTC disable function is not working as expected

a particular would be on an RX-8 on top mount Turbo installs for example. disabling the OMP fuel pump altogether. without it detected it goes to safe mode. in my particular case it is removal of catalytic converter and removal of rear O2 sensor altogether, and removal of the air pump (the one used w...
by Walle
September 3rd, 2021, 10:17 am
Forum: Software Support
Topic: DTC disable function is not working as expected
Replies: 12
Views: 14551

Re: DTC disable function is not working as expected

Why is this not implemented like in Mazda Edit whre a PID check can be completely disabled? (To prevent safe mod etc if "cryptical components are removed.
by Walle
August 29th, 2021, 8:29 pm
Forum: Software Support
Topic: DTC disable function is not working as expected
Replies: 12
Views: 14551

Re: DTC disable function is not working as expected

Can you comfirm on what the DTC disable actually does ? I have an OBD display as a monitoring to the car always on (instead of GPS) with some additional important information that reads error codes etc. Does it only stops the engine malfunction light come on, or is it also disabling checking of thes...