Search found 513 matches
- February 16th, 2024, 1:57 am
- Forum: Software Support
- Topic: Error service 36
- Replies: 1
- Views: 690
Re: Error service 36
There are three possible causes: 1. The ECU may sometimes be stuck in some non-standard mode. Disconnect the battery for 10 minutes to fully reset it and try again. 2. There may be some kind of aftermarket devices connected to the CAN bus of the vehicle, such as gauges, loggers, modules that control...
- February 7th, 2024, 2:40 am
- Forum: Series I Tuning
- Topic: Tune Sharing
- Replies: 12
- Views: 13840
Re: Tune Sharing
hi guys, can anyone tell me if it's possible or if you can adapt one of your maps with the lite version? rx8 2003 streetport decat panel filter sl exhaust terminal sohn kit ngk coils The Lite version can only flash official tunes and tunes built by professional tuning partners. Community tunes can ...
- February 5th, 2024, 3:47 am
- Forum: Software Support
- Topic: Seeking assistance with connectivity
- Replies: 1
- Views: 708
Re: Seeking assistance with connectivity
Replied via email.
- January 8th, 2024, 9:32 am
- Forum: Software Support
- Topic: Flat foot shifting on nd miata
- Replies: 5
- Views: 1659
Re: Flat foot shifting on nd miata
Yes, ND will come next. VersaTuner Lite will be enough to use launch control and no lift shifting.
- January 2nd, 2024, 8:29 am
- Forum: Software Support
- Topic: Flat foot shifting on nd miata
- Replies: 5
- Views: 1659
Re: Flat foot shifting on nd miata
Do you have an ND or ND2?
- December 27th, 2023, 3:51 am
- Forum: Announcements
- Topic: VersaTuner 22.1 released
- Replies: 3
- Views: 57173
Re: VersaTuner 22.1 released
I recently purchased Versatuner through Fab9 and flashed my 2013 Mazda Miata NC3. I was contraplating purchasing the upgraded version that would allow me to make changes myself. First I would like to find manual, list of codes, etc that I could read about how to make the changes myself first. I tri...
- December 20th, 2023, 8:15 am
- Forum: Series I Tuning
- Topic: 4-Port Base Map
- Replies: 5
- Views: 2164
Re: 4-Port Base Map
You are correct, this is an error in our launch control implementation for this car. Please change the rev limiter to 7500 if you wish to retain factory behavior. The error will be corrected in a future update.
- December 19th, 2023, 8:06 am
- Forum: Series I Tuning
- Topic: 4-Port Base Map
- Replies: 5
- Views: 2164
Re: 4-Port Base Map
What is your ECU calibration?
- December 11th, 2023, 8:16 am
- Forum: BK Mazda3
- Topic: Table labeling
- Replies: 1
- Views: 1441
Re: Table labeling
The ECU code is not documented and it is a very time consuming process to identify the exact conditions under which each table is used. As a result, when the conditions are not known, the tables are labeled with numbers (1, 2, 3...) In reality one of them could be "normal", another one cou...
- December 7th, 2023, 7:36 am
- Forum: Software Support
- Topic: Crackle N Pop tune Problems
- Replies: 2
- Views: 1672
Re: Crackle N Pop tune Problems
Currently you need to have the accelerator slightly pressed in to get crackles and pops on the SkyActiv-G engine. If you release the accelerator pedal completely, the ECU will shut off fuel and no crackles will be produced. When you downshift, don't release the accelerator completely, keep it presse...