Search found 1314 matches
- March 4th, 2024, 12:21 am
- Forum: Mazda 2.3 DISI Turbo
- Topic: Speed 3 1st gen wont idle
- Replies: 1
- Views: 285
Re: Speed 3 1st gen wont idle
Well, you need a MAF calibration for that intake. The engine will not stay running with such a big difference in air flow. Download the MAF calibration from here: https://corksport.com/support/instructi ... ration.txt and add it to your tune.
- February 10th, 2024, 2:36 pm
- Forum: Software Support
- Topic: Unable to Update
- Replies: 1
- Views: 265
Re: Unable to Update
Probably it passed more than 1 year since your last update. Log into your account at versatuner.com, go to Versatuner -> Licenses and Downloads -> Versatuner Downloads, download Versatuner run that file to perform update. See if that works, it should. Once you do that you should be able to download ...
- December 9th, 2023, 9:14 pm
- Forum: ND
- Topic: ND1 Turbo with 3Bar MAP sensor has a limit around 5500rpm
- Replies: 3
- Views: 1719
Re: ND1 Turbo with 3Bar MAP sensor has a limit around 5500rpm
Ok, and what tune are you using? Did you change any of the existing tunes, you're using an OTS tune, a custom tune made by somebody else? Can you post it here?
- December 5th, 2023, 1:11 am
- Forum: Mazda6 Tuning
- Topic: Learn values
- Replies: 1
- Views: 2657
Re: Learn values
Every system has default calibrations. However, these things may have variations from the defaults which are more like a point of reference rather than a target. By example air flow. The same volume of air at a given temperature and atmospheric pressure will have a different weight (actual mass) at ...
- December 4th, 2023, 7:08 am
- Forum: Gen 2 Tuning
- Topic: Deactivate pops & crackles in the lower RPMs
- Replies: 19
- Views: 34283
Re: Deactivate pops & crackles in the lower RPMs
If you have HPFP internals and you do not enjoy the pops&bangs I suggest you try the high load + cai + racepipe after you install all these mods...
- November 27th, 2023, 4:41 am
- Forum: ND
- Topic: ND1 Turbo with 3Bar MAP sensor has a limit around 5500rpm
- Replies: 3
- Views: 1719
Re: ND1 Turbo with 3Bar MAP sensor has a limit around 5500rpm
What tune are you using?
- November 21st, 2023, 1:16 am
- Forum: MAZDASPEED3/Mazda 3 MPS Tuning
- Topic: Question about MAP sensor settings
- Replies: 3
- Views: 1336
Re: Question about MAP sensor settings
Yes this is just a reiteration of the old Bosch 3BAR MAP sensor, so you can use offset 5.41, scalar 1 = 65.78 and scalar 2 = 1
- November 21st, 2023, 1:06 am
- Forum: MAZDASPEED3/Mazda 3 MPS Tuning
- Topic: Question about MAP sensor settings
- Replies: 3
- Views: 1336
Re: Question about MAP sensor settings
I think we can calculate the parameters for this one, I found the specs here:
https://www.bosch-motorsport-shop.com.a ... 1012130444
https://www.bosch-motorsport-shop.com.a ... 1012130444
- November 17th, 2023, 6:53 am
- Forum: Series I Tuning
- Topic: Full Bridgeport Idle
- Replies: 8
- Views: 2446
- October 30th, 2023, 7:22 am
- Forum: MAZDASPEED6/Mazda 6 MPS Tuning
- Topic: ignition timing
- Replies: 9
- Views: 20143
Re: ignition timing
On what fueling were you targeting 11.5-12* degrees at redline? I’m tuning for ethanol now on E30 and currently have my timing at 12* degrees at redline. I was obviously speaking of pump gas. With E30 you can run quite a bit leaner and add a ton more timing. If "redline" for you means 650...