Search found 1317 matches
- August 28th, 2023, 1:46 am
- Forum: Mazda 2.3 DISI Turbo
- Topic: My car won't pop, burble or crackle
- Replies: 7
- Views: 2100
Re: My car won't pop, burble or crackle
You've set it to -20 BUT the timing you are getting is like 5 and the load does not go below 0.22 under decel (or if it does it comes back up quickly). Also in your log you have some useless parameters such as fuel injection amount and catalyst temperature (on a catless car!!) but no AFR/Lambda, des...
- August 24th, 2023, 12:43 am
- Forum: MAZDASPEED3/Mazda 3 MPS Tuning
- Topic: Fmic tuning
- Replies: 2
- Views: 1520
Re: Fmic tuning
...and of course upload the log here so that we can look at it.
- August 24th, 2023, 12:43 am
- Forum: MAZDASPEED3/Mazda 3 MPS Tuning
- Topic: Fmic tuning
- Replies: 2
- Views: 1520
Re: Fmic tuning
What intake do you have? Usually the engine will die because of improperly calibrated MAF or because you have a huge leak somewhere. Load this logging preset: https://www.dropbox.com/s/xowaxd4zho576se/Full-3MPSBK-Logging.vtpre?dl=0 - start logging the moment you put the key on, and stop logging afte...
- August 24th, 2023, 12:22 am
- Forum: Mazda 2.3 DISI Turbo
- Topic: Tuning Troubles
- Replies: 29
- Views: 24089
Re: Tuning Troubles
I suggest to use the MAP values as safety limits and not target them at this point. Use the factory logic based on load because it simply works best.
- August 23rd, 2023, 4:55 pm
- Forum: Mazda 2.3 DISI Turbo
- Topic: Tuning Troubles
- Replies: 29
- Views: 24089
Re: Tuning Troubles
Where can I find the WGDC for the setup? Boost Control -> BCS DC Base Extended. I read not too long ago where I saw you say you can set all values to 0 then set the increase amount to 100% and let the ECU decide where it wants it. Then implement those in and repeat a couple times till it settles. I...
- August 23rd, 2023, 12:44 am
- Forum: Mazda 2.3 DISI Turbo
- Topic: Tuning Troubles
- Replies: 29
- Views: 24089
Re: Tuning Troubles
What's the process in tuning the BCS DC? You just look at what WGDC is required for your setup to reach the set load target and you put that value in for 70-ish APP and up, and then interpolate linearly with what's below - or you pull those intermediate load values from some normal driving logs ins...
- August 22nd, 2023, 9:58 pm
- Forum: Mazda 2.3 DISI Turbo
- Topic: Tuning Troubles
- Replies: 29
- Views: 24089
Re: Tuning Troubles
Just set the throttle reduction MAP limits to like 246-248kPa and the fuel cut MAP limits to 252/254. The factory MAP sensor will read up to 256-257kPa and 252 is not a problem. The factory turbo is capable of 240-245-ish kPa MAP with very free flowing breathing mods so at least past 5k RPM it will ...
- August 21st, 2023, 7:08 pm
- Forum: Mazda 2.3 DISI Turbo
- Topic: Tuning Troubles
- Replies: 29
- Views: 24089
Re: Tuning Troubles
Well, you are reaching and exceeding the throttle reduction MAP limits. That's the reason you do not see any increase.
- July 24th, 2023, 6:51 pm
- Forum: Gen 2 Tuning
- Topic: Pops and bangs
- Replies: 1
- Views: 3107
Re: Pops and bangs
You should check with your tuner. You can't edit the tunes from a Pro Tuner.
- July 12th, 2023, 11:02 pm
- Forum: Mazda 2.3 DISI Turbo
- Topic: P2610 after Reflash with the new Version
- Replies: 5
- Views: 10734
Re: P2610 after Reflash with the new Version
Ok, the error came back. Previous owner doesn't have the original firmware file VIN.bck any more. Not sure how to go about this one. Since the check engine comes back only after the car is started cold after sitting a while and not during driving it I'm kind of tempted to suppress this PID from vers...