VersaTuner does not delete the source files if you delete the tunes from "My Tunes" and vice versa.
To get the stock tune, just click "New Tune" and the stock tune will load in the Tune Editor.
Search found 513 matches
- July 21st, 2023, 6:04 am
- Forum: Series I Tuning
- Topic: Stock tune for 2004 6 speed RX-8
- Replies: 1
- Views: 1301
- July 20th, 2023, 7:08 pm
- Forum: Mazda 2.3 DISI Turbo
- Topic: Help request
- Replies: 1
- Views: 1199
Re: Help request
You need to calibrate your MAF. Due to the much larger MAF housing, the ECU is getting incorrect information about the amount of air flowing in.
You will also need to tune for the larger turbo. There is no way you can run these mods without a proper tune.
You will also need to tune for the larger turbo. There is no way you can run these mods without a proper tune.
- July 20th, 2023, 7:05 pm
- Forum: Software Support
- Topic: ECU not supported Message
- Replies: 1
- Views: 1178
Re: ECU not supported Message
You did everything correctly by providing the necessary data to the calibration team. Support for your calibration will be added in 1-2 business days. There are a lot of different ECU types and versions for each Mazda model and while we support most of them out the box, some are new or not seen to u...
- July 20th, 2023, 7:02 pm
- Forum: Software Support
- Topic: Another incorrect VIN
- Replies: 2
- Views: 4275
Re: Another incorrect VIN
Letters O and I are not allowed in VINs, it's always zero and one. VersaTuner website will check the VIN when you type it.
But if you make a mistake, just contact our support and we will correct the VIN for you.
But if you make a mistake, just contact our support and we will correct the VIN for you.
- July 14th, 2023, 6:26 pm
- Forum: Software Support
- Topic: Versatune install error
- Replies: 5
- Views: 1737
Re: Versatune install error
There's not much we can do. Those devices constantly query the ECU and interfere with the flash process. They will interfere with any tuning solution you decide to use. You don't need to completely remove them. Just disconnect them from power or from the CAN bus for 1 hour while you reflash the ECU.
- July 14th, 2023, 8:14 am
- Forum: Software Support
- Topic: Versatune install error
- Replies: 5
- Views: 1737
Re: Versatune install error
Then you probably have some other device connected to the CAN bus or the OBD-II port of the vehicle. Gauges, loggers, alarms, modules that keep the lights or radio on. Common culprits are devices made by MX-5 Things.
You will need to disconnect them temporarily while you are reflashing the ECU.
You will need to disconnect them temporarily while you are reflashing the ECU.
- July 14th, 2023, 7:33 am
- Forum: Software Support
- Topic: Versatune install error
- Replies: 5
- Views: 1737
Re: Versatune install error
What car do you have? Do you currently have an aftermarket tune on the ECU? Does it fail right away or somewhere in the middle?
- July 14th, 2023, 1:47 am
- Forum: Software Support
- Topic: Retrieve Current Tune
- Replies: 3
- Views: 3927
Re: Retrieve Current Tune
Responded via email.
- June 7th, 2023, 9:40 pm
- Forum: Software Support
- Topic: Flash or recovery impossible...
- Replies: 1
- Views: 3240
Re: Flash or recovery impossible...
This error can mean one of two things: 1. The ECU is stuck in some weird state after the last reflash. Try disconnecting the battery for a few minutes to reset it and then try again. 2. The ECU was tuned previously with a tuning solution that locks it on a deep level. It has not been tuned with Vers...
- May 25th, 2023, 10:01 pm
- Forum: Feature Requests
- Topic: Flashing VersaTune over EcuTek
- Replies: 3
- Views: 3664
Re: Flashing VersaTune over EcuTek
You can try.