New User

Discussion of tuning specific to MAZDASPEED6/MAZDASPEED Atenza/Mazda 6 MPS vehicles

Re: New User

by mituc » December 11th, 2017, 8:06 pm

So the MAF calibration logs look good. I'm a little concerned about the high fuel trims in the first part of the MAF curve, up until like 2 Volts or so when the LTFTs are 16-17% which is high, but that is idle/low RPM air flow so at least for now it should not be a concern.

Above like 2.5V the MAF calibration is spot on.

Either way just to be sure take a look under the hood and make sure there is no leak between the MAF and turbo. It may be a small leak that closes when the vacuum in the intake increases (turbo spinning faster), therefore sometimes just repositioning all the hoses and re-tightening all the clamps may help.
2008 Cosmic Blue Mazda 3MPS
Build engine + WMI + GTX3071, ~476WHP @31-32PSI
2008 Icy Blue Mazda CX7
Stock engine, intake and exhaust (YES!!), GTX2867 gen2 + Autotech HPFP, self-tuned to 320-ish BHP
VersaTuner guru
 
Posts: 881
Joined: December 17th, 2011, 2:47 pm
Location: Iasi/Romania

Re: New User

by mteogr » December 12th, 2017, 2:32 am

I will check for air leaks.
What's is your opinion for the knock retard in one log?
 
Posts: 23
Joined: October 17th, 2017, 11:22 am

Re: New User

by mituc » December 12th, 2017, 2:43 am

There is absolutely no knock retard in your logs. You should try the 98RON tune if right now you have 98-100RON gas in the tank.
Low timing + high octane gas means high exhaust temperatures and over time the exhaust valve seals will cook and there's going to be also a lot of soot coming out of the engine, and part of it will come back into the intake via the EGR.
2008 Cosmic Blue Mazda 3MPS
Build engine + WMI + GTX3071, ~476WHP @31-32PSI
2008 Icy Blue Mazda CX7
Stock engine, intake and exhaust (YES!!), GTX2867 gen2 + Autotech HPFP, self-tuned to 320-ish BHP
VersaTuner guru
 
Posts: 881
Joined: December 17th, 2011, 2:47 pm
Location: Iasi/Romania

Re: New User

by mteogr » December 12th, 2017, 9:24 am

I will flash a new tune with 98 base and maf calibration for Cobb intake . I will also check for leaks.
Which dashboard preset is StockCar Monitoring 2?
 
Posts: 23
Joined: October 17th, 2017, 11:22 am

Re: New User

by mituc » December 12th, 2017, 6:09 pm

mteogr wrote:Which dashboard preset is StockCar Monitoring 2?


The one from the second DropBox link I've sent you a few posts above.
2008 Cosmic Blue Mazda 3MPS
Build engine + WMI + GTX3071, ~476WHP @31-32PSI
2008 Icy Blue Mazda CX7
Stock engine, intake and exhaust (YES!!), GTX2867 gen2 + Autotech HPFP, self-tuned to 320-ish BHP
VersaTuner guru
 
Posts: 881
Joined: December 17th, 2011, 2:47 pm
Location: Iasi/Romania

Re: New User

by mteogr » December 13th, 2017, 2:31 pm

Sorry mituc.
My mistake.
I had not downloaded the preset when I made the wot runs and I realized it now.
Do you want to do wot with this preset?

I would like also to tell me your opinion.
When I finished my new tune, with your maf calibration for Cobb intake and the Base 93US/98EU, I tried to make a comparison between this 2 tunes.

I saw that there are big differences at the Absolut Limits/Load Targeting Tables.

for example:

Base 91US/95EU / Base 95US/98EU

Closed Loop Load Limit 1,2,3 2,5 / 3
Load Limit Force Spark Retard 2,5 / 3
Neutral/Reverse Max Load High BAT 1,693 / 3
Neutral/Reverse Max Load Low BAT 1,693 / 3
Operating Load Limit 1 0,803-0,856-0,911 and then 2,5 / 3 at all RPM
Operating Load Limit 2 0.803-0,883-1.019 and then 2.5 / 3 at all RPM
Requested Load Limit Overall 2 / 3
Requested Load Limit RPM 2 / 3

I found it weird.
Is this ok?
 
Posts: 23
Joined: October 17th, 2017, 11:22 am

Re: New User

by mituc » December 13th, 2017, 6:15 pm

You will never reach those values anyway and they are set for the logic of the tune, not for its functionality on the car. In your case it they are set at 2.2, 2.5, 2.7, 3, 3.5 or 4 makes absolutely no difference.
2008 Cosmic Blue Mazda 3MPS
Build engine + WMI + GTX3071, ~476WHP @31-32PSI
2008 Icy Blue Mazda CX7
Stock engine, intake and exhaust (YES!!), GTX2867 gen2 + Autotech HPFP, self-tuned to 320-ish BHP
VersaTuner guru
 
Posts: 881
Joined: December 17th, 2011, 2:47 pm
Location: Iasi/Romania

Re: New User

by mteogr » December 16th, 2017, 2:35 am

So I can change this values from 95 base to 98 base without problem or affect the operation of the engine.
Thank you mituc.
 
Posts: 23
Joined: October 17th, 2017, 11:22 am

Re: New User

by mituc » December 16th, 2017, 8:39 am

mteogr wrote:So I can change this values from 95 base to 98 base without problem or affect the operation of the engine.


If you really want that... it's not necessary but changing them will not affect the logic of the tune or the way it performs.
2008 Cosmic Blue Mazda 3MPS
Build engine + WMI + GTX3071, ~476WHP @31-32PSI
2008 Icy Blue Mazda CX7
Stock engine, intake and exhaust (YES!!), GTX2867 gen2 + Autotech HPFP, self-tuned to 320-ish BHP
VersaTuner guru
 
Posts: 881
Joined: December 17th, 2011, 2:47 pm
Location: Iasi/Romania

Previous

Who is online
Users browsing this forum: No registered users and 6 guests