Page 1 of 1
New User First Log. High Load OTS Map
Posted: November 5th, 2018, 6:08 am
by miket55
Hello,
Just purchased VersaTuner and joined the forum.
FLashed the high load map to my Mazda 6 Mps which standard apart from a Jetex cat back.
I am new to tuning but trying to learn as much as possible.
Would someone mind just glancing over my first log.
The first two sections are 30-80 mph in 3rd gear and the final one is a 40-100 mph in 4th.
I can't see anything too nasty going on but I am a newbie. No knock at all but the WGDC does hit 100% at times?
Let me know what you experts think please.
Cheers Mike.
Re: New User First Log. High Load OTS Map
Posted: November 20th, 2018, 5:58 pm
by mituc
Where are you located? I'm curious because it seems to be very hot there.
Re: New User First Log. High Load OTS Map
Posted: November 21st, 2018, 4:39 am
by miket55
South of England. Is that from looking at the BAT's?
Temperature has been around 50-55 degrees Fahrenheit when i took that log. Boost temps of 99 degree F are quite normal?
Re: New User First Log. High Load OTS Map
Posted: November 21st, 2018, 5:35 am
by mituc
Oh I'm sorry, the temperatures are in F and I was thinking in C, the first line of the sheet was not expanding properly.
Everything looks good now that I'm reading it correctly. It looks like it was a 3rd gear log even though I wish you logged the engine RPM as well.
Re: New User First Log. High Load OTS Map
Posted: November 21st, 2018, 12:04 pm
by miket55
Thank you for having a look. I will post some more logs soon and include rpm. Trying to get the AFR's as precise as possible then increasing loads a touch then maybe try advancing the timing slightly and see how that goes as I have 0 knock at present. Obviously I want to keep it that way but maybe there is room for a bit of timing adjustment.
I don't think I can increase the loads much more as the boost is hitting 18 and 19 at certain points but the WGDC is hitting 100%
Let me know your thoughts.
Re: New User First Log. High Load OTS Map
Posted: November 21st, 2018, 7:40 pm
by mituc
Re: New User First Log. High Load OTS Map
Posted: November 23rd, 2018, 12:55 am
by miket55
Made a few adjustments to the base map and have improved the 40-100 by 0.7 seconds. I don't think there is much more i can squeeze out of it before replacing the stock intake and TIP. Hitting almost 240 g/s and from what i have read that is a pretty decent figure for a stock car?
Re: New User First Log. High Load OTS Map
Posted: November 23rd, 2018, 2:09 am
by mituc
240g/s is indeed decent. This may actually be the flow limit of the factory intake with that turbo. I managed to push mine to 260g/s though.
Send me your current map somehow (pm, dropbox, google drive, whatever), and I'll change it for you based on the CX7 map I was running when the CX7 was bone stock (including the HPFP).
Also please let me know what fuel you're using (brand and type).
Re: New User First Log. High Load OTS Map
Posted: November 23rd, 2018, 3:56 am
by miket55
Thank you. I don't currently have up- rated HPFP internals but the fuel pressures seem ok so far.
I always use shell V-power rated at 99 octane.
I have attached the current map for you to look at.
Cheers
Mike
Re: New User First Log. High Load OTS Map
Posted: November 24th, 2018, 3:59 am
by mituc
Ok, you're good... it seems like you're already pushing it more than I did without fuel pump internals...