Looking for a Base Tune for a Catted DP + TMIC + 3" intake

Tuning discussion for all second generation Mazda 2.3 MZR DISI Turbo powered vehicles
Post Reply
5hiftyy
Posts: 4
Joined: March 17th, 2021, 5:23 am

Looking for a Base Tune for a Catted DP + TMIC + 3" intake

Post by 5hiftyy »

I'll be installing a bunch of fast bits onto my Gen2 this weekend. The mostly comprehensive list is as follows:
  • HPFP
  • 3" Intake
  • Upgraded CPe Intercooler
  • Catted CPe Downpipe
  • Maybe EBCS, if I get the fittings in on time
I had planned on throwing on a 'base tune' that mostly covered what I was installing, but the ones I can see listed don't include an aftermarket catted downpipe. They all say "stock DP required." I was hoping someone here might have a tune they've done for a similar parts list that I could start off with, and continue to MAF Cal/log/tweak/update from there.

TIA!
mituc
VersaTuner guru
Posts: 1323
Joined: December 17th, 2011, 2:47 pm
Location: Iasi/Romania

Re: Looking for a Base Tune for a Catted DP + TMIC + 3" intake

Post by mituc »

What 3" intake you have?
What EBCS do you have and how do you plan to set it up: 3port or bleed/2port?
Is your versatuner the full version?
What gas are you using?
2008 Cosmic Blue Mazda 3MPS
Built engine + WMI + GTX3071 gen2, ~509BHP @34PSI
2008 Icy Blue Mazda CX7
Stock engine and exhaust (YES!!), JBR3" + GTX2867 gen2 + Autotech HPFP, self-tuned to 330-ish BHP
5hiftyy
Posts: 4
Joined: March 17th, 2021, 5:23 am

Re: Looking for a Base Tune for a Catted DP + TMIC + 3" intake

Post by 5hiftyy »

I don't know why, but I didn't see this reply, so first thank you for replying so quick despite my own reply being late af. I'll answer your questions below:
What 3" intake you have?
JBR All-Aluminum 3" intake
What EBCS do you have and how do you plan to set it up: 3port or bleed/2port?
I have a MAC35 EBCS and can set it up in 2 or 3-port, whichever is better/easier. Haven't hooked it up yet.
Is your versatuner the full version?
Yes.
What gas are you using?
I'm running on 93octane (North American) now with the 93 high-load map for the stock downpipe.

I don't have the HF DP installed yet, nor the EBCS. I will be installing it in a couple weeks, and would like to have a tune ready to go when I do!

Anyway, thanks again for the effort, it's appreciated.
mituc
VersaTuner guru
Posts: 1323
Joined: December 17th, 2011, 2:47 pm
Location: Iasi/Romania

Re: Looking for a Base Tune for a Catted DP + TMIC + 3" intake

Post by mituc »

Here it is. Your setup requires some logging to make sure it's all good and if everything looks ok you will be able to extract a bit more performance out of it.
2008 Cosmic Blue Mazda 3MPS
Built engine + WMI + GTX3071 gen2, ~509BHP @34PSI
2008 Icy Blue Mazda CX7
Stock engine and exhaust (YES!!), JBR3" + GTX2867 gen2 + Autotech HPFP, self-tuned to 330-ish BHP
5hiftyy
Posts: 4
Joined: March 17th, 2021, 5:23 am

Re: Looking for a Base Tune for a Catted DP + TMIC + 3" intake

Post by 5hiftyy »

This is amazing.... Thank you!! I will do some logs and such once it's all back together. This is a huge help, thanks!!
Post Reply