ECU Calibration

Discussion of tuning specific to Mazda6 SkyActiv Diesel vehicles
Post Reply
sss222sss
Posts: 5
Joined: September 22nd, 2020, 11:53 pm

ECU Calibration

Post by sss222sss »

Hello,

Id like to install Versatune in my car but before that I would like to know which version I allready have in my car (for backup).

My ECU calibration is: SHYJEB000SH0B060

Is it official or ... ?

VIN: JMZGJ692821187769
Platform: Gen3 Mazda 6 SkyActiv-D
ECU calibration: SHYJEB000SH0B060

Thanks
User avatar
Ugnius @ VersaTune
Lead developer
Posts: 579
Joined: March 19th, 2010, 11:57 am

Re: ECU Calibration

Post by Ugnius @ VersaTune »

You have SHYJEB calibration, it is the latest official calibration for your car. VersaTuner base ROM for your car is also based on SHYJEB.
sss222sss
Posts: 5
Joined: September 22nd, 2020, 11:53 pm

Re: ECU Calibration

Post by sss222sss »

Thank fo your answer.

One more question. Now I have my boost pressure lower than desired - Manifold Absolute Pressure is 20-40kPa lower than Manifold Absolute Pressure Desired. In some conditions (high load, high RPM) its almost the same (my VT logs in attachments). Also during regeneration its the same.
I have checked intake manifold, EGR + EGR Cooler Bypass Valve (cleaned), MAP (cleaned), MAF (replaced), O2 sensor (replaced), Exhaust Gas Pressure Sensor (cleaned), turbocharger + regulation (chcecked, OK) but no change.

No error code, fuel consumption is aprox 7,8l/100km (36 mpg).

Is it normal or issue? Can I install Versatune?
Attachments
VersaTuner Logs - standard.zip
(294.62 KiB) Downloaded 210 times
VersaTuner Logs - regenration.zip
(461.96 KiB) Downloaded 240 times
shr3k
Posts: 25
Joined: February 2nd, 2017, 6:17 am

Re: ECU Calibration

Post by shr3k »

sss222sss wrote: September 28th, 2020, 9:58 pmNow I have my boost pressure lower than desired - Manifold Absolute Pressure is 20-40kPa lower than Manifold Absolute Pressure Desired. In some conditions (high load, high RPM) its almost the same (my VT logs in attachments). Also during regeneration its the same.
IMO is it perfectly normal, during regeneration, the EGR valves are closed. Check PID BOOST_A_STATUS in ForScan (dunno if VT displays, I'm on vacation now) at full throttle. It should stick on Closed Loop during acceleration without shifting, not switch between Open/Closed or oscillate too much.
2004 Mazda3 Sedan 1.6 MZ-CD 115hp; 2007 Mazda5 2.0 MZR-CD 145hp; 2009 Mazda6 WGN 2.2 MZR-CD 185hp, 2014 Mazda6 WGN 2.2 CD 175hp A/T VersaTuned - my exs
2019 Mazda2 1.5 A/T 90hp selftuned, 2018 Opel Insignia Country Tourer 2.0T 4x4 320hp EDS Phase 2+
sss222sss
Posts: 5
Joined: September 22nd, 2020, 11:53 pm

Re: ECU Calibration

Post by sss222sss »

I dont understand how BOOST_A_STATUS should change depending on THROTTLE POSITION...

BOOST_A_STATUS: 0=CLOSED LOOP, 100=OPEN LOOP
Attachments
Nová bitová mapa.jpg
Nová bitová mapa.jpg (300.61 KiB) Viewed 8259 times
shr3k
Posts: 25
Joined: February 2nd, 2017, 6:17 am

Re: ECU Calibration

Post by shr3k »

Better post data than this lo-res chart...

Odesláno z mého MI 9 pomocí Tapatalk

2004 Mazda3 Sedan 1.6 MZ-CD 115hp; 2007 Mazda5 2.0 MZR-CD 145hp; 2009 Mazda6 WGN 2.2 MZR-CD 185hp, 2014 Mazda6 WGN 2.2 CD 175hp A/T VersaTuned - my exs
2019 Mazda2 1.5 A/T 90hp selftuned, 2018 Opel Insignia Country Tourer 2.0T 4x4 320hp EDS Phase 2+
sss222sss
Posts: 5
Joined: September 22nd, 2020, 11:53 pm

Re: ECU Calibration

Post by sss222sss »

XLS file attached, if you can help...
Attachments
Mazda 6.xlsx
(338.85 KiB) Downloaded 229 times
shr3k
Posts: 25
Joined: February 2nd, 2017, 6:17 am

Re: ECU Calibration

Post by shr3k »

sss222sss wrote: October 5th, 2020, 8:27 pm XLS file attached, if you can help...
However unusable (very few lines when filtered to load>90 and full throttle). In addition, it is necessary to log time since engine started, revolutions per minute, vehicle speed and accelerator position.
2004 Mazda3 Sedan 1.6 MZ-CD 115hp; 2007 Mazda5 2.0 MZR-CD 145hp; 2009 Mazda6 WGN 2.2 MZR-CD 185hp, 2014 Mazda6 WGN 2.2 CD 175hp A/T VersaTuned - my exs
2019 Mazda2 1.5 A/T 90hp selftuned, 2018 Opel Insignia Country Tourer 2.0T 4x4 320hp EDS Phase 2+
sss222sss
Posts: 5
Joined: September 22nd, 2020, 11:53 pm

Re: ECU Calibration

Post by sss222sss »

Ok, one more try...
However, the file is too large - uploaded to my Google Drive:
https://drive.google.com/file/d/1yVp_Mp ... sp=sharing
shr3k
Posts: 25
Joined: February 2nd, 2017, 6:17 am

Re: ECU Calibration

Post by shr3k »

You're just joking, 240 records out of 12186 are APP_REL > 90. But about runtime 370 you can see constant APP 94.12 with BOOST_A_STATUS suddenly switched from Closed to Open. But from my POV, I've seen more oscillations with clogged intake/MAP sensors.
bs.PNG
bs.PNG (81.22 KiB) Viewed 8072 times
2004 Mazda3 Sedan 1.6 MZ-CD 115hp; 2007 Mazda5 2.0 MZR-CD 145hp; 2009 Mazda6 WGN 2.2 MZR-CD 185hp, 2014 Mazda6 WGN 2.2 CD 175hp A/T VersaTuned - my exs
2019 Mazda2 1.5 A/T 90hp selftuned, 2018 Opel Insignia Country Tourer 2.0T 4x4 320hp EDS Phase 2+
Post Reply