P0335 code

Tuning discussion for all first generation Mazda RX-8 (2004-2008)
Monstermills
Posts: 16
Joined: January 25th, 2021, 6:33 am

P0335 code

Post by Monstermills »

I have an 05, new reman Bennett Built coils, stock air box with K&N air filter, stock header with cat less 2.5” mid pipe and HKS hi power catback.

I flashed this tune and after my first drive cycle I received a P0335 essentric shaft position sensor.

6port/revi/midpipe/catback/BHR D585 coils
Version 1.13
91US/95EU Octane tune for 6 port RX-8 with Racing Beat REVi intake and full Racing Beat exhaust and D585 style coils. Modified AFRs, dwell, and VDI settings provide horsepower and torque gains across the entire power band. 9700 rev limit. Slightly increased metering oil pump output for increased longevity.

I examined the sensor, cleaned and even replaced with a new one. I cleared the code with 20 brake step and pulling battery wire a few times and without having to start the car the code kept coming up. I cleared any masked mil codes as well and reflashed the tune.

I went back to a prior tune version 1.05 and the code instantly disappeared.

Would there be solutions for this, I would like to accommodate the new coils if possible.

Thanks in advance,
Clinton
User avatar
Steve @ VersaTune
Lead tuner
Posts: 1157
Joined: March 29th, 2010, 12:58 pm

Re: P0335 code

Post by Steve @ VersaTune »

What is the calibration ID?
Monstermills
Posts: 16
Joined: January 25th, 2021, 6:33 am

Re: P0335 code

Post by Monstermills »

ECU calibration N3ZBEJ00013H6020
User avatar
Steve @ VersaTune
Lead tuner
Posts: 1157
Joined: March 29th, 2010, 12:58 pm

Re: P0335 code

Post by Steve @ VersaTune »

Please try this tune. I set dwell to stock.

Did you have any issues with any other tunes?
Attachments
Test tune P0335 troubleshooting v1.00.vtune
(8.11 KiB) Downloaded 232 times
Monstermills
Posts: 16
Joined: January 25th, 2021, 6:33 am

Re: P0335 code

Post by Monstermills »

I’ll try this new one you have out, thank you.

I haven’t had any issues with the current version 1.05. I have only tried this tune so far.
Monstermills
Posts: 16
Joined: January 25th, 2021, 6:33 am

Re: P0335 code

Post by Monstermills »

I just flashed the test tune p0335 and the check engine light appeared.

I flashed the version 1.04 and no check engine on that tune, so 1.04 and 1.05 no DTC
User avatar
Steve @ VersaTune
Lead tuner
Posts: 1157
Joined: March 29th, 2010, 12:58 pm

Re: P0335 code

Post by Steve @ VersaTune »

There are only a few differences between those tunes. I made a few changes. Please try this one.
Attachments
Test tune P0335 troubleshooting v1.01.vtune
(8 KiB) Downloaded 215 times
Monstermills
Posts: 16
Joined: January 25th, 2021, 6:33 am

Re: P0335 code

Post by Monstermills »

This one had the same code p0335 come on again.

Thank you again for your efforts,

Clinton
User avatar
Steve @ VersaTune
Lead tuner
Posts: 1157
Joined: March 29th, 2010, 12:58 pm

Re: P0335 code

Post by Steve @ VersaTune »

We're running out of tables that could possibly be the problem.
Here is another to try.
Attachments
Test tune P0335 troubleshooting v1.03.vtune
(6.75 KiB) Downloaded 216 times
dcox11b
Posts: 25
Joined: March 9th, 2021, 1:28 pm
Location: USA
Contact:

Re: P0335 code

Post by dcox11b »

1. Try flashing one of Steve's tunes

2. Give your e shaft sensor a quick cleaning its easy to reach with a rag and some spray cleaner

3. Before you start the car after flashing the new tune, turn the key in to the on (but not engine on) and stomp your brake pedal about 25 times as fast as you can and you should see the oil pressure needle swee0 across the the ranges.

4. Turn key off

5. Start as normal
2005 Rx8 Shinka - Black Cherry Mica
Post Reply