Hi
I just got a Obdlink SX and trying the versatuner to detect the car but connection fails and the error says " could not detect OBDlink baud rate..; \
It works on OBDwiz software where one can set baud rate to 1000000! but does not work with lower rate! How can we set Baud rate on Versatuner? thanks for tip.
BR,
Could not detect OBDlink SX baud rate...
Could not detect OBDlink SX baud rate...
Last edited by amiara on April 15th, 2022, 7:57 am, edited 1 time in total.
Re: Could not detect OBDlink SX baud rate...
In the OBDLink software try setting the BAUD rate to AUTO and see if it starts going.
2008 Cosmic Blue Mazda 3MPS
Built engine + WMI + GTX3071 gen2, ~509BHP @34PSI
2008 Icy Blue Mazda CX7
Stock engine and exhaust (YES!!), JBR3" + GTX2867 gen2 + Autotech HPFP, self-tuned to 330-ish BHP
Built engine + WMI + GTX3071 gen2, ~509BHP @34PSI
2008 Icy Blue Mazda CX7
Stock engine and exhaust (YES!!), JBR3" + GTX2867 gen2 + Autotech HPFP, self-tuned to 330-ish BHP
Re: Could not detect OBDlink SX baud rate...
I found that it does not work with baud rates lower than 1000000!! how to set Baud rate on Versatuner?
Re: Could not detect OBDlink SX baud rate...
I don't think you're supposed to set any baud rate in versatuner for this adapter, you should set it in the STN application or whatever comes with the tool.
2008 Cosmic Blue Mazda 3MPS
Built engine + WMI + GTX3071 gen2, ~509BHP @34PSI
2008 Icy Blue Mazda CX7
Stock engine and exhaust (YES!!), JBR3" + GTX2867 gen2 + Autotech HPFP, self-tuned to 330-ish BHP
Built engine + WMI + GTX3071 gen2, ~509BHP @34PSI
2008 Icy Blue Mazda CX7
Stock engine and exhaust (YES!!), JBR3" + GTX2867 gen2 + Autotech HPFP, self-tuned to 330-ish BHP
Re: Could not detect OBDlink SX baud rate...
Yes on STN tool ,it only works with Baud Rate 1000000!! on OBDwiz tool also works with 1000000! but there is no COM setting on Versatuner.
Re: Could not detect OBDlink SX baud rate...
I think you are supposed to configure the adapter in the system using the STN tool (or ifprep2?), and once it becomes available in the system you will be able to select it in the versatuner (or any other software that can use or needs a similar interface) as well.
2008 Cosmic Blue Mazda 3MPS
Built engine + WMI + GTX3071 gen2, ~509BHP @34PSI
2008 Icy Blue Mazda CX7
Stock engine and exhaust (YES!!), JBR3" + GTX2867 gen2 + Autotech HPFP, self-tuned to 330-ish BHP
Built engine + WMI + GTX3071 gen2, ~509BHP @34PSI
2008 Icy Blue Mazda CX7
Stock engine and exhaust (YES!!), JBR3" + GTX2867 gen2 + Autotech HPFP, self-tuned to 330-ish BHP
- Ugnius @ VersaTune
- Lead developer
- Posts: 590
- Joined: March 19th, 2010, 11:57 am
Re: Could not detect OBDlink SX baud rate...
VersaTuner tries different baud rates automatically, but 1000000 is not one of them, that's why the cable is not detected.
We will fix that in an update and publish it today or tomorrow.
We will fix that in an update and publish it today or tomorrow.
- Ugnius @ VersaTune
- Lead developer
- Posts: 590
- Joined: March 19th, 2010, 11:57 am
Re: Could not detect OBDlink SX baud rate...
The fix has been published.
-
- Posts: 1
- Joined: July 26th, 2023, 12:16 pm
Re: Could not detect OBDlink SX baud rate...
I'm getting a error code :ft_invalid_baud_rate any ideas