Hello everybody,
This is supposed to work pretty much like the OTS maps. It's not about spoon feeding, it's just about providing the newcomers with decent MAF calibrations that are known to work decently.
These calibrations, as far as I know, should work in exactly the same way no matter the car model, so we should be able to reuse a, say, Cobb SRI MAF cal from a MS3 owner on a MS6.
Please keep in mind that there are a few reasons why pretty much any car is unique, so is the MAF cal:
- elevation;
- average ambient temperature;
- not everybody's MAF is super uber clean;
So I may have -2/+2 LTFT's with a MAF cal on my car and someone else may get 0/+4 with the same depending on how much dirt is on my MAF or on his, the ambient temperatures differ significantly (more than 10C), and so on.
However, as long as a MAF cal is scaled decently and works on a car, once the receiver car will learn the trims everything should be fine.
For starters, here's my Cobb SRI MAF cal. My fuel trims are in the -1/+3 % range, I tried to fix even these points but it's actually pretty hard to get all the surrounding values scaled as I get 0 LTFT's with those. So I just left it as it is.
The OL part should be like 0.5-1.0 % richer.
All this happens at 0C - +6C as I've got the versatuner in late December and didn't have the opportunity to re-work my MAF cal in +20C weather or more.
Share your MAF Calibration
Share your MAF Calibration
- Attachments
-
- MAF_CAL_mituc-CobbSRI-20120313.zip
- (599 Bytes) Downloaded 1176 times
2008 Cosmic Blue Mazda 3MPS
Built engine + WMI + GTX3071 gen2, ~509BHP @34PSI
2008 Icy Blue Mazda CX7
Stock engine and exhaust (YES!!), JBR3" + GTX2867 gen2 + Autotech HPFP, self-tuned to 330-ish BHP
Built engine + WMI + GTX3071 gen2, ~509BHP @34PSI
2008 Icy Blue Mazda CX7
Stock engine and exhaust (YES!!), JBR3" + GTX2867 gen2 + Autotech HPFP, self-tuned to 330-ish BHP
-
- Posts: 383
- Joined: August 3rd, 2011, 11:29 am
Re: Share your MAF Calibration
Excellent idea, I'll upload my corksport sri+tip cal later.
Re: Share your MAF Calibration
Hi there,
Here is mine for SURE Aeros without TIP. LTFTs are:
0.0% from 0 g/s to 5.70 g/s.
-3.1% from 5.71 g/s. to 18 g/s.
-0.8% from 18.01 g/s. to 30 g/s.
0.0% from 30.01 g/s. to 70 g/s.
0.0% from 70.01 g/s. to top g/s.
It was done a couple of weeks ago so winter calibration with temperatures from 2º to 12º and I will update it after a new recalibration and I'll finish it for OL.
Cheers.
Here is mine for SURE Aeros without TIP. LTFTs are:
0.0% from 0 g/s to 5.70 g/s.
-3.1% from 5.71 g/s. to 18 g/s.
-0.8% from 18.01 g/s. to 30 g/s.
0.0% from 30.01 g/s. to 70 g/s.
0.0% from 70.01 g/s. to top g/s.
It was done a couple of weeks ago so winter calibration with temperatures from 2º to 12º and I will update it after a new recalibration and I'll finish it for OL.
Cheers.
- Attachments
-
- MAF_CAL_keridil-SUREAeros-20120316.csv.zip
- (1.1 KiB) Downloaded 1111 times
Mazda 6 MPS, BPV GFB, RX-8 wheels, B8 + Eibach Pro-Kit, CS 3" SRI, GS EBCS (interrupt), CS 3" TMIC, EGR off, HPFP internals, CS catted downpipe, 3 bar MAP, BNRS3, forged engine and stuff
Re: Share your MAF Calibration
New version of my MAL calibration, finished by now.
For SURE Aeros without TIP, no test pipe, stock TMIC and no downcat. [Note:] As pointed later all mods no relevant to MAF calibration except the SRI.
I logged it today with 20º and the results for my defined breakpoints are:
Cheers.
For SURE Aeros without TIP, no test pipe, stock TMIC and no downcat. [Note:] As pointed later all mods no relevant to MAF calibration except the SRI.
I logged it today with 20º and the results for my defined breakpoints are:
- 0 - 5.7 g/s -> 0 LTFT
- 5.7 - 18 g/s -> 0 LTFT
- 18 - 30 g/s -> -1.6 LTFT
- 30 - 70 g/s -> 1.6 LTFT
- 70 - 120 g/s -> 0 LTFT
- 120 - 150 g/s -> 0 LTFT
- 150 - up g/s -> 0 LTFT
Cheers.
- Attachments
-
- Base 93US_98EU Octane High Load + SURE SRI v1.04.vtune.zip
- (44.92 KiB) Downloaded 1093 times
Last edited by keridil on March 26th, 2012, 2:41 am, edited 1 time in total.
Mazda 6 MPS, BPV GFB, RX-8 wheels, B8 + Eibach Pro-Kit, CS 3" SRI, GS EBCS (interrupt), CS 3" TMIC, EGR off, HPFP internals, CS catted downpipe, 3 bar MAP, BNRS3, forged engine and stuff
Re: Share your MAF Calibration
I wonder if you guys are watching only the LTFT's (which are 0 in OL) or you're looking at the commanded and requested AFR values as well.
P.S.: the other mods such as intercooler, exhaust, whatever, are not relevant for a MAF cal.
P.S.: the other mods such as intercooler, exhaust, whatever, are not relevant for a MAF cal.
2008 Cosmic Blue Mazda 3MPS
Built engine + WMI + GTX3071 gen2, ~509BHP @34PSI
2008 Icy Blue Mazda CX7
Stock engine and exhaust (YES!!), JBR3" + GTX2867 gen2 + Autotech HPFP, self-tuned to 330-ish BHP
Built engine + WMI + GTX3071 gen2, ~509BHP @34PSI
2008 Icy Blue Mazda CX7
Stock engine and exhaust (YES!!), JBR3" + GTX2867 gen2 + Autotech HPFP, self-tuned to 330-ish BHP
Re: Share your MAF Calibration
Hi there,mituc wrote:I wonder if you guys are watching only the LTFT's (which are 0 in OL) or you're looking at the commanded and requested AFR values as well.
P.S.: the other mods such as intercooler, exhaust, whatever, are not relevant for a MAF cal.
I didn't say anything about it, but in OL my lambda AFR values are in a range of +-0.20, normally +-0.10, so they are good to go.
I though that TIP and TMIC affect MAF readings, am I wrong?
Cheers.
Mazda 6 MPS, BPV GFB, RX-8 wheels, B8 + Eibach Pro-Kit, CS 3" SRI, GS EBCS (interrupt), CS 3" TMIC, EGR off, HPFP internals, CS catted downpipe, 3 bar MAP, BNRS3, forged engine and stuff
- Steve @ VersaTune
- Lead tuner
- Posts: 1157
- Joined: March 29th, 2010, 12:58 pm
Re: Share your MAF Calibration
Usually the only thing that affects the MAF cal is any change in shape of the pre-maf intake piping or diameter of the MAF housing.
Re: Share your MAF Calibration
Yeah, of course! Excuse me for shutting my brain off!Steve @ VersaTune wrote:Usually the only thing that affects the MAF cal is any change in shape of the pre-maf intake piping or diameter of the MAF housing.
![Sad :(](./images/smilies/icon_e_sad.gif)
I was talking about mass air flow (g/s), if there are less restrictions in place my car will breath "faster".
Cheers.
Mazda 6 MPS, BPV GFB, RX-8 wheels, B8 + Eibach Pro-Kit, CS 3" SRI, GS EBCS (interrupt), CS 3" TMIC, EGR off, HPFP internals, CS catted downpipe, 3 bar MAP, BNRS3, forged engine and stuff
Re: Share your MAF Calibration
Interesting, after having a 3" TBE fitted my MAF calibration was all over the place and the same occurred recently after fitting the DNP manifold and BNR stage 2 turbo.Steve @ VersaTune wrote:Usually the only thing that affects the MAF cal is any change in shape of the pre-maf intake piping or diameter of the MAF housing.
Re: Share your MAF Calibration
Definitely this.Steve @ VersaTune wrote:Usually the only thing that affects the MAF cal is any change in shape of the pre-maf intake piping or diameter of the MAF housing.
Also, if the gas you're using has any added methanol (E5, E10) this will have a slight effect on the the LTFT's and the actual AFR's as well. Not that much at this concentration, but if you know you should state what is the E-rating of the gas you were using for your MAF calibration.
2008 Cosmic Blue Mazda 3MPS
Built engine + WMI + GTX3071 gen2, ~509BHP @34PSI
2008 Icy Blue Mazda CX7
Stock engine and exhaust (YES!!), JBR3" + GTX2867 gen2 + Autotech HPFP, self-tuned to 330-ish BHP
Built engine + WMI + GTX3071 gen2, ~509BHP @34PSI
2008 Icy Blue Mazda CX7
Stock engine and exhaust (YES!!), JBR3" + GTX2867 gen2 + Autotech HPFP, self-tuned to 330-ish BHP