BNR S3 with Grimmspeed 3 port - Running on Spring Pressure

Discussion of tuning specific to MAZDASPEED6/MAZDASPEED Atenza/Mazda 6 MPS vehicles
Post Reply
Jugmeister
Posts: 6
Joined: August 24th, 2015, 6:04 pm

BNR S3 with Grimmspeed 3 port - Running on Spring Pressure

Post by Jugmeister »

Planning on installing a BNR S3 next weekend so i'm wanting to start off on spring pressure before tuning. I'm running the Base 93US/98EU High Load - Grimmspeed Interrupt OTS map.

Wondering how i can achieve this, from what i have read (i think) i need to reduce the cells in the BCS DC Base Extended table to 0%. Is it really that simple or are there other things than need to be changed with having the Grimmspeed BCS in interrupt mode?

Any guidance would be appreciated, thanks.
User avatar
Steve @ VersaTune
Lead tuner
Posts: 1157
Joined: March 29th, 2010, 12:58 pm

Re: BNR S3 with Grimmspeed 3 port - Running on Spring Pressu

Post by Steve @ VersaTune »

Set "BCS DC Adjustment Limit - Increase" to zero as well or you will get up to 20% duty cycle.
Jugmeister
Posts: 6
Joined: August 24th, 2015, 6:04 pm

Re: BNR S3 with Grimmspeed 3 port - Running on Spring Pressu

Post by Jugmeister »

Steve @ VersaTune wrote:Set "BCS DC Adjustment Limit - Increase" to zero as well or you will get up to 20% duty cycle.
Thanks Steve gives me some peace of mind I'm doing it right. Can't wait to get it on an get in dialed in Image


Sent from my iPhone using Tapatalk
mazda62006
Posts: 12
Joined: December 2nd, 2016, 12:58 pm

Re: BNR S3 with Grimmspeed 3 port - Running on Spring Pressu

Post by mazda62006 »

I know this is old but I'm getting ready to install the same setup. What do I need to do to tune for this setup. I'm new to the mazda speed 6 but have tuned a eclipse 4g63. Is there a tuning guide somewhere? Just need to understand the tables that or out there. Any help you can provide would be great.
mituc
VersaTuner guru
Posts: 1323
Joined: December 17th, 2011, 2:47 pm
Location: Iasi/Romania

Re: BNR S3 with Grimmspeed 3 port - Running on Spring Pressu

Post by mituc »

So you can start load one of the high load tunes, zero out all the "BCSDC Base" table and see where spring pressure gets you. Once you see that you can start populating that table.

Just look at the tables in the tune and if you tuned an eclipse already you will figure things out pretty quickly.

As for tuning guides - you can look around and compare the tunes you have available on-line, also look on these posts here:
http://www.versatune.net/forum/viewforum.php?f=5 (http://www.versatune.net/forum/viewtopic.php?f=5&t=983 http://www.versatune.net/forum/viewtopic.php?f=5&t=988 and so on) and once you have more questions just ask them here.
2008 Cosmic Blue Mazda 3MPS
Built engine + WMI + GTX3071 gen2, ~509BHP @34PSI
2008 Icy Blue Mazda CX7
Stock engine and exhaust (YES!!), JBR3" + GTX2867 gen2 + Autotech HPFP, self-tuned to 330-ish BHP
mazda62006
Posts: 12
Joined: December 2nd, 2016, 12:58 pm

Re: BNR S3 with Grimmspeed 3 port - Running on Spring Pressu

Post by mazda62006 »

thanks for the reply, will start reading and trying to make sure I have a good base line understanding
mazda62006
Posts: 12
Joined: December 2nd, 2016, 12:58 pm

Re: BNR S3 with Grimmspeed 3 port - Running on Spring Pressu

Post by mazda62006 »

Okay so I'm ready to try my hand a load tuning but unsure where to start exactly. Which tables should I start with? I running the a BNR stage 3, downpipe, upgraded top mount, and 3 bar map. Also have the hpfp internal which I will be installing. I'm just not clear on which of the load tables I should be changing.
thanks
mituc
VersaTuner guru
Posts: 1323
Joined: December 17th, 2011, 2:47 pm
Location: Iasi/Romania

Re: BNR S3 with Grimmspeed 3 port - Running on Spring Pressu

Post by mituc »

This is that moment when you should start looking for an e-tuner.
2008 Cosmic Blue Mazda 3MPS
Built engine + WMI + GTX3071 gen2, ~509BHP @34PSI
2008 Icy Blue Mazda CX7
Stock engine and exhaust (YES!!), JBR3" + GTX2867 gen2 + Autotech HPFP, self-tuned to 330-ish BHP
Post Reply